Some RVers think of rubber roofs as inferior to aluminum or fiberglass roofs, but the simple fact is that most RVs hve one, and a rubber roof can last for 20 years or longer—if it is properly maintained. Of course, maintenance is up to you, the owner.
Periodic maintenance performed on the rubber roof membrane helps to protect the wood roof panels beneath it and the interior of your RV from leaks. Spring is a good time to check your rubber roof for damage, clean it and seal leaks.
If the roof is beyond repair, spring also is a good time to replace one. That’s a labor-intensive job that you may want to leave to a pro, but be warned: Rubber roof replacement, including the membrane and damaged wood panels underneath, can cost $4,000 to $10,000, depending on where you have the work done and the size of your rig. Get competing, detailed estimates before agreeing to have the work done.
Repairs are affordable, especially if you handle them yourself. Whether you do may depend on how capable you are of working on the roof and a ladder, and how comfortable you are with doing that. You can repair spots that have been torn or gouged, or you can replace sections.
Types of Rubber Roofs
Two types of rubber roofing are used on RVs:
Your RV owner’s manual should tell you which kind your RV has, and how to care for it. If the manual is missing, call the customer service number for the RV manufacturer and give the service rep your serial number. The manufacturer should be able to tell you what is covering your roof.
Cleaning a Rubber Roof
Sweep the debris from your roof.
Now inspect. Look for cracks, tears and gouges. Inspect not just the roof membrane, but also the sealant around anything that juts through the roof membrane, including fans, vents, skylights, air-conditioning units and electronics.
Before you wash the roof, use vinyl tape to temporarily seal leaks you uncover.
There’ one other important step before you wash the roof: Wash, or at least rinse with a hose or pressure washer, the vertical areas of the RV first, including the front, back and sides. That prevents hard-to-remove streaks on the vertical areas that runoff from the dirty roof might create.
Use a mild soap, such as Murphy’s Oil Soap, or a dedicated RV rubber roof cleane, mixed with water. Do not use a cleaner containing petroleum distillates, citrus or abrasives, all of which can damage rubber membranes. Scrub using a sponge mop or medium-bristle brush on a long handle. If your roof is not meant to be walked on, walk or stand on pieces of plywood that you lay atop the roof.
Rinse with a garden hose, or better, a pressure washer, set to no more than 1,200 pounds per square inch. Higher pressure could damage the roof membrane.
Patching Rubber Membranes
For gouges, tears and cracks, often caused by tree limbs scraping or striking the surface, cut away any loose rubber from the clean, damaged area of the rubber membrane using a utility knife and a scraper. Be careful not to cause more damage to the plywood beneath the membrane. The membrane is glued to the plywood, so a flat-blade scraper may be needed to carefully remove damaged sections of the rubber.
If the plywood is gouged, fill the damaged area with Dicor self-leveling sealant and allow it to cure. Do not use a silicone sealant because roof coatings and patches will not stick to it.
The wounded area, now enlarged, will need to be covered and sealed. Use Eternabond tapes or patches, or a similar product, and cut to size with scissors, generously but not excessively overlapping sound parts of the membrane around the wound. Eternabond and similar products have a sticky side that goes against the old membrane and plywood. They come in various widths and lengths. Keep leftovers for on-the-road repairs after mishaps with trees. Warning: Patching tapes won’t budge once in place, so align patches carefully and roll them out as flat as possible. If the tape has a protective layer on the outer surface, pull it back and discard it.
Smooth the patch by hand, then roll air pockets and loose areas flat, using a small roller, such as a wallpaper roller. Start in the center of the patch and work your way out.
Apply Dicor self-leveling sealant to the edges of the patch a maximum-strength seal against water. While you have your Dicor in hand, patch any cracked or leaky beads around roof-mounted accessories, such as fan and vent openings.
Sealing the Roof
Finish off your roof repairs and maintenance by coating the entire roof with a rubber roof-compatible sealant, such as Heng’s Rubber Roof Coating or 303 Protectant. Apply according to directions, typically with a paint-type roller and long handle. The sealant will make the roof even more waterproof. Just as importantly, the sealcoat will protect the membrane from the sunlight’s ultraviolet rays, which can dry and crack a membrane over time.
Check your roof periodically and do spot repairs as needed. A roof gets dirty nd dusty, so wash it at least one additional time during the season and before storing your rig.